109 lines
2.6 KiB
C
109 lines
2.6 KiB
C
#include "app_config.h"
|
||
|
||
#include "system/includes.h"
|
||
#include "device/includes.h"
|
||
#include "asm/includes.h"
|
||
|
||
// *INDENT-OFF*
|
||
|
||
UART1_PLATFORM_DATA_BEGIN(uart1_data)
|
||
.baudrate = 115200,
|
||
.port = PORTUSB_A,
|
||
.tx_pin = IO_PORT_USB_DPA,
|
||
.rx_pin = IO_PORT_USB_DMA,
|
||
.max_continue_recv_cnt = 1024,
|
||
.idle_sys_clk_cnt = 500000,
|
||
.clk_src = PLL_48M,
|
||
.flags = UART_DEBUG,
|
||
UART1_PLATFORM_DATA_END();
|
||
|
||
|
||
UART2_PLATFORM_DATA_BEGIN(uart2_data)
|
||
.baudrate = 115200,
|
||
.port = PORT_REMAP,
|
||
.output_channel = OUTPUT_CHANNEL0,
|
||
.tx_pin = IO_PORTB_03,
|
||
.rx_pin = -1,
|
||
.max_continue_recv_cnt = 1024,
|
||
.idle_sys_clk_cnt = 500000,
|
||
.clk_src = PLL_48M,
|
||
.flags = UART_DEBUG,
|
||
UART2_PLATFORM_DATA_END();
|
||
|
||
|
||
/************************** LOW POWER config ****************************/
|
||
static const struct low_power_param power_param = {
|
||
.config = TCFG_LOWPOWER_LOWPOWER_SEL,
|
||
.btosc_disable = TCFG_LOWPOWER_BTOSC_DISABLE, //进入低功耗时BTOSC是否保持
|
||
.vddiom_lev = TCFG_LOWPOWER_VDDIOM_LEVEL, //强VDDIO等级,可选：2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.4V 3.6V
|
||
.vddiow_lev = TCFG_LOWPOWER_VDDIOW_LEVEL, //弱VDDIO等级,可选：2.1V 2.4V 2.8V 3.2V
|
||
.vdc14_dcdc = TRUE, //打开内部1.4VDCDC，关闭则用外部
|
||
.vdc14_lev = VDC14_VOL_SEL_LEVEL, //VDD1.4V配置
|
||
.sysvdd_lev = SYSVDD_VOL_SEL_LEVEL, //内核、sdram电压配置
|
||
.vlvd_enable = TRUE, //TRUE电压复位使能
|
||
.vlvd_value = VLVD_SEL_25V, //低电压复位电压值
|
||
};
|
||
|
||
#if defined CONFIG_BT_ENABLE || defined CONFIG_WIFI_ENABLE
|
||
#include "wifi/wifi_connect.h"
|
||
const struct wifi_calibration_param wifi_calibration_param = {
|
||
.xosc_l = 0xb,// 调节左晶振电容
|
||
.xosc_r = 0xb,// 调节右晶振电容
|
||
.pa_trim_data ={1, 7, 4, 7, 11, 1, 7},// 根据MP测试生成PA TRIM值
|
||
.mcs_dgain ={
|
||
50,//11B_1M
|
||
50,//11B_2.2M
|
||
50,//11B_5.5M
|
||
50,//11B_11M
|
||
|
||
72,//11G_6M
|
||
72,//11G_9M
|
||
85,//11G_12M
|
||
80,//11G_18M
|
||
64,//11G_24M
|
||
64,//11G_36M
|
||
62,//11G_48M
|
||
52,//11G_54M
|
||
|
||
72,//11N_MCS0
|
||
90,//11N_MCS1
|
||
80,//11N_MCS2
|
||
64,//11N_MCS3
|
||
64,//11N_MCS4
|
||
64,//11N_MCS5
|
||
50,//11N_MCS6
|
||
43,//11N_MCS7
|
||
}
|
||
};
|
||
#endif
|
||
|
||
REGISTER_DEVICES(device_table) = {
|
||
{"uart1", &uart_dev_ops, (void *)&uart1_data },
|
||
{"uart2", &uart_dev_ops, (void *)&uart2_data },
|
||
{"rtc", &rtc_dev_ops, NULL},
|
||
};
|
||
|
||
#ifdef CONFIG_DEBUG_ENABLE
|
||
void debug_uart_init()
|
||
{
|
||
uart_init(&uart2_data);
|
||
}
|
||
#endif
|
||
|
||
void board_early_init()
|
||
{
|
||
devices_init();
|
||
}
|
||
|
||
static void board_power_init(void)
|
||
{
|
||
power_init(&power_param);
|
||
}
|
||
void board_init()
|
||
{
|
||
board_power_init();
|
||
adc_init();
|
||
}
|
||
|
||
|