481 lines
14 KiB
C
481 lines
14 KiB
C
#include "app_config.h"
|
||
#include "system/includes.h"
|
||
#include "device/iic.h"
|
||
#include "server/audio_dev.h"
|
||
#include "asm/includes.h"
|
||
|
||
#if TCFG_USB_SLAVE_ENABLE || TCFG_USB_HOST_ENABLE
|
||
#include "otg.h"
|
||
#include "usb_host.h"
|
||
#include "usb_common_def.h"
|
||
#include "usb_storage.h"
|
||
#endif
|
||
|
||
// *INDENT-OFF*
|
||
|
||
UART0_PLATFORM_DATA_BEGIN(uart0_data)
|
||
.baudrate = 115200,
|
||
/* .baudrate = 1000000, */
|
||
/* .port = PORTA_5_6, */
|
||
/* .port = PORTB_1_0, */
|
||
.port = PORTA_3_4,
|
||
/* .port = PORTH_0_1, */
|
||
/* .tx_pin = IO_PORTA_05, */
|
||
/* .rx_pin = IO_PORTA_06, */
|
||
/* .tx_pin = IO_PORTB_01, */
|
||
/* .rx_pin = IO_PORTB_00, */
|
||
.tx_pin = IO_PORTA_03,
|
||
.rx_pin = IO_PORTA_04,
|
||
/* .tx_pin = IO_PORTH_00, */
|
||
/* .rx_pin = IO_PORTH_01, */
|
||
.max_continue_recv_cnt = 1024,
|
||
.idle_sys_clk_cnt = 500000,
|
||
.clk_src = PLL_48M,
|
||
.flags = UART_DEBUG,
|
||
UART0_PLATFORM_DATA_END();
|
||
|
||
|
||
UART1_PLATFORM_DATA_BEGIN(uart1_data)
|
||
.baudrate = 1000000,
|
||
/* .port = PORT_REMAP, */
|
||
/* .port = PORTH_6_7, */
|
||
/* .port = PORTC_3_4, */
|
||
/* .port = PORTUSB_B, */
|
||
.port = PORTUSB_A,
|
||
/* .tx_pin = IO_PORTH_06, */
|
||
/* .rx_pin = IO_PORTH_07, */
|
||
/* .tx_pin = IO_PORTC_03, */
|
||
/* .rx_pin = IO_PORTC_04, */
|
||
/* .tx_pin = IO_PORT_USB_DPB, */
|
||
/* .rx_pin = IO_PORT_USB_DMB, */
|
||
.tx_pin = IO_PORT_USB_DPA,
|
||
.rx_pin = IO_PORT_USB_DMA,
|
||
/* .tx_pin = IO_PORTB_06, */
|
||
/* .rx_pin = IO_PORTB_07, */
|
||
.max_continue_recv_cnt = 1024,
|
||
.idle_sys_clk_cnt = 500000,
|
||
.clk_src = PLL_48M,
|
||
.flags = UART_DEBUG,
|
||
UART1_PLATFORM_DATA_END();
|
||
|
||
|
||
UART2_PLATFORM_DATA_BEGIN(uart2_data)
|
||
.baudrate = 1000000,
|
||
/* .port = PORTH_2_3, */
|
||
/* .port = PORTC_9_10, */
|
||
/* .port = PORTB_6_7, */
|
||
/* .port = PORTE_0_1, */
|
||
/* .tx_pin = IO_PORTH_02, */
|
||
/* .rx_pin = IO_PORTH_03, */
|
||
/* .tx_pin = IO_PORTC_09, */
|
||
/* .rx_pin = IO_PORTC_10, */
|
||
/* .tx_pin = IO_PORTB_06, */
|
||
/* .rx_pin = IO_PORTB_07, */
|
||
/* .tx_pin = IO_PORTE_00,*/
|
||
/* .rx_pin = IO_PORTE_01,*/
|
||
.port = PORT_REMAP,
|
||
.output_channel = OUTPUT_CHANNEL0,
|
||
.tx_pin = IO_PORTC_06,
|
||
.rx_pin = -1,
|
||
.max_continue_recv_cnt = 1024,
|
||
.idle_sys_clk_cnt = 500000,
|
||
.clk_src = PLL_48M,
|
||
.flags = UART_DEBUG,
|
||
UART2_PLATFORM_DATA_END();
|
||
|
||
|
||
|
||
/****************SD模块**********************************************************
|
||
* 暂只支持1个SD外设，如需要多个SD外设，自行去掉下面SD0/1_ENABLE控制，另外定义即可
|
||
********************************************************************************/
|
||
#if TCFG_SD0_ENABLE
|
||
//sd0
|
||
#define SD_PLATFORM_DATA_BEGIN() SD0_PLATFORM_DATA_BEGIN(sd0_data)
|
||
#define SD_PLATFORM_DATA_END() SD0_PLATFORM_DATA_END()
|
||
#define SD_CLK_DETECT_FUNC sdmmc_0_clk_detect
|
||
#elif TCFG_SD1_ENABLE
|
||
//sd1
|
||
#define SD_PLATFORM_DATA_BEGIN() SD1_PLATFORM_DATA_BEGIN(sd1_data)
|
||
#define SD_PLATFORM_DATA_END() SD1_PLATFORM_DATA_END()
|
||
#define SD_CLK_DETECT_FUNC sdmmc_1_clk_detect
|
||
#endif
|
||
|
||
#if (TCFG_SD0_ENABLE || TCFG_SD1_ENABLE)
|
||
SD_PLATFORM_DATA_BEGIN()
|
||
.port = TCFG_SD_PORTS,
|
||
.priority = 3,
|
||
.data_width = TCFG_SD_DAT_WIDTH,
|
||
.speed = TCFG_SD_CLK,
|
||
.detect_mode = TCFG_SD_DET_MODE,
|
||
#if (TCFG_SD_DET_MODE == SD_CLK_DECT)
|
||
.detect_func = SD_CLK_DETECT_FUNC,
|
||
#elif (TCFG_SD_DET_MODE == SD_IO_DECT)
|
||
.detect_func = sdmmc_0_io_detect,
|
||
#else
|
||
.detect_func = NULL,
|
||
#endif
|
||
SD_PLATFORM_DATA_END()
|
||
#endif
|
||
/****************SD模块*********************/
|
||
|
||
|
||
HW_IIC0_PLATFORM_DATA_BEGIN(hw_iic1_data)
|
||
/* .clk_pin = IO_PORTC_01, */
|
||
/* .dat_pin = IO_PORTC_02, */
|
||
.clk_pin = IO_PORTH_00,
|
||
.dat_pin = IO_PORTH_01,
|
||
.baudrate = 0x3f,//3f:385k
|
||
HW_IIC0_PLATFORM_DATA_END()
|
||
|
||
SW_IIC_PLATFORM_DATA_BEGIN(sw_iic0_data)
|
||
/*.clk_pin = IO_PORTA_03,*/
|
||
/*.dat_pin = IO_PORTA_04,*/
|
||
.clk_pin = IO_PORTC_01,
|
||
.dat_pin = IO_PORTC_02,
|
||
.sw_iic_delay = 50,
|
||
SW_IIC_PLATFORM_DATA_END()
|
||
/*
|
||
* spi0接falsh
|
||
*/
|
||
SPI0_PLATFORM_DATA_BEGIN(spi0_data)
|
||
.clk = 20000000,
|
||
.mode = SPI_STD_MODE,
|
||
.port = 'A',
|
||
SPI0_PLATFORM_DATA_END()
|
||
|
||
SPI1_PLATFORM_DATA_BEGIN(spi1_data)
|
||
.clk = 80000000,
|
||
.mode = SPI_STD_MODE,
|
||
.attr = SPI_MODE_SLAVE | SPI_SCLK_H_UPL_SMPL | SPI_UNIDIR_MODE,//从机，CLK高 更新数据高，单向模式(SPI_DO单线)
|
||
.port = 'B',
|
||
SPI1_PLATFORM_DATA_END()
|
||
|
||
SPI2_PLATFORM_DATA_BEGIN(spi2_data)
|
||
.clk = 20000000,
|
||
.mode = SPI_STD_MODE,
|
||
.attr = SPI_SCLK_H_UPH_SMPL | SPI_BIDIR_MODE,//主机，CLK高 更新数据高，双向模式(SPI_DI/SPI_DO双线)
|
||
.port = 'C',
|
||
SPI2_PLATFORM_DATA_END()
|
||
|
||
static const struct spiflash_platform_data spiflash_data = {
|
||
.name = "spi0",
|
||
.mode = FAST_READ_OUTPUT_MODE,//FAST_READ_IO_MODE,
|
||
.sfc_run_mode = SFC_FAST_READ_DUAL_OUTPUT_MODE,
|
||
};
|
||
|
||
static const struct dac_platform_data dac_data = {
|
||
.pa_auto_mute = 1,
|
||
.pa_mute_port = 0xff,
|
||
.pa_mute_value = 1,
|
||
.differ_output = 0,
|
||
.hw_channel = 0x01,
|
||
.ch_num = 1, //差分只需开一个通道
|
||
.vcm_init_delay_ms = 1000,
|
||
};
|
||
static const struct adc_platform_data adc_data = {
|
||
.mic_channel = LADC_CH_MIC1_P_N,
|
||
.mic_ch_num = 1,
|
||
.isel = 2,
|
||
};
|
||
static const struct audio_pf_data audio_pf_d = {
|
||
.adc_pf_data = &adc_data,
|
||
.dac_pf_data = &dac_data,
|
||
};
|
||
static const struct audio_platform_data audio_data = {
|
||
.private_data = (void *) &audio_pf_d,
|
||
};
|
||
|
||
|
||
#ifdef CONFIG_VIDEO_ENABLE
|
||
#define CAMERA_GROUP_PORT ISC_GROUPA
|
||
/* #define CAMERA_GROUP_PORT ISC_GROUPC */
|
||
static const struct camera_platform_data camera0_data = {
|
||
.xclk_gpio = IO_PORTC_00,//注意： 如果硬件xclk接到芯片IO，则会占用OUTPUT_CHANNEL1
|
||
.reset_gpio = IO_PORTC_03,
|
||
.online_detect = NULL,
|
||
.pwdn_gpio = -1,
|
||
.power_value = 0,
|
||
.interface = SEN_INTERFACE0,//SEN_INTERFACE_CSI2,
|
||
.dvp={
|
||
#if (CAMERA_GROUP_PORT == ISC_GROUPA)
|
||
.pclk_gpio = IO_PORTA_08,
|
||
.hsync_gpio = IO_PORTA_09,
|
||
.vsync_gpio = IO_PORTA_10,
|
||
#else
|
||
.pclk_gpio = IO_PORTC_08,
|
||
.hsync_gpio = IO_PORTC_09,
|
||
.vsync_gpio = IO_PORTC_10,
|
||
#endif
|
||
.group_port = CAMERA_GROUP_PORT,
|
||
.data_gpio={
|
||
#if (CAMERA_GROUP_PORT == ISC_GROUPA)
|
||
IO_PORTA_07,
|
||
IO_PORTA_06,
|
||
IO_PORTA_05,
|
||
IO_PORTA_04,
|
||
IO_PORTA_03,
|
||
IO_PORTA_02,
|
||
IO_PORTA_01,
|
||
IO_PORTA_00,
|
||
-1,
|
||
-1,
|
||
#else
|
||
IO_PORTC_07,
|
||
IO_PORTC_06,
|
||
IO_PORTC_05,
|
||
IO_PORTC_04,
|
||
IO_PORTC_03,
|
||
IO_PORTC_02,
|
||
IO_PORTC_01,
|
||
IO_PORTC_00,
|
||
-1,
|
||
-1,
|
||
#endif
|
||
},
|
||
}
|
||
};
|
||
static const struct video_subdevice_data video0_subdev_data[] = {
|
||
{ VIDEO_TAG_CAMERA, (void *)&camera0_data },
|
||
};
|
||
static const struct video_platform_data video0_data = {
|
||
.data = video0_subdev_data,
|
||
.num = ARRAY_SIZE(video0_subdev_data),
|
||
};
|
||
#endif
|
||
|
||
PWM_PLATFORM_DATA_BEGIN(pwm_data0)
|
||
.port = 0,
|
||
.pwm_ch = PWMCH0_H | PWMCH0_L,//初始化可选多通道,如:PWMCH0_H | PWMCH0_L | PWMCH1_H ... | PWMCH7_H | PWMCH7_L | PWM_TIMER2_OPCH2 | PWM_TIMER3_OPCH3 ,
|
||
.freq = 1000,//频率
|
||
.duty = 50,//占空比
|
||
.point_bit = 0,//根据point_bit值调节占空比小数点精度位: 0<freq<=4K,point_bit=2;4K<freq<=40K,point_bit=1; freq>40K,point_bit=0;
|
||
PWM_PLATFORM_DATA_END()
|
||
|
||
PWM_PLATFORM_DATA_BEGIN(pwm_data1)
|
||
.port = IO_PORTA_03,//选择定时器的TIMER PWM任意IO，pwm_ch加上PWM_TIMER3_OPCH3或PWM_TIMER2_OPCH2有效,只支持2个PWM,占用output_channel2/3，其他外设使用output_channel需留意
|
||
.pwm_ch = PWM_TIMER2_OPCH2,//初始化可选多通道,如:PWMCH0_H | PWMCH0_L | PWMCH1_H ... | PWMCH7_H | PWMCH7_L | PWM_TIMER2_OPCH2 | PWM_TIMER3_OPCH3 ,
|
||
.freq = 1000,//频率
|
||
.duty = 50,//占空比
|
||
.point_bit = 0,//根据point_bit值调节占空比小数点精度位: 0<freq<=4K,point_bit=2;4K<freq<=40K,point_bit=1; freq>40K,point_bit=0;
|
||
PWM_PLATFORM_DATA_END()
|
||
|
||
#if TCFG_USB_SLAVE_ENABLE || TCFG_USB_HOST_ENABLE
|
||
static const struct otg_dev_data otg_data = {
|
||
.usb_dev_en = 0x03,
|
||
#if TCFG_USB_SLAVE_ENABLE
|
||
.slave_online_cnt = 10,
|
||
.slave_offline_cnt = 10,
|
||
#endif
|
||
#if TCFG_USB_HOST_ENABLE
|
||
.host_online_cnt = 10,
|
||
.host_offline_cnt = 10,
|
||
#endif
|
||
.detect_mode = OTG_HOST_MODE | OTG_SLAVE_MODE | OTG_CHARGE_MODE,
|
||
.detect_time_interval = 30,
|
||
};
|
||
#endif
|
||
|
||
#if defined CONFIG_BT_ENABLE || defined CONFIG_WIFI_ENABLE
|
||
#include "wifi/wifi_connect.h"
|
||
const struct wifi_calibration_param wifi_calibration_param = {
|
||
.xosc_l = 0xb,// 调节晶振左电容
|
||
.xosc_r = 0xb,// 调节晶振右电容
|
||
.pa_trim_data ={1, 7, 4, 7, 11, 1, 7},// 根据MP测试生成PA TRIM值
|
||
};
|
||
#endif
|
||
|
||
#ifdef CONFIG_RTC_ENABLE
|
||
const struct rtc_init_config rtc_init_data = {
|
||
.rtc_clk_sel = RTC_CLK_SEL_INSIDE,
|
||
.rtc_power_sel = RTCVDD_SUPPLY_OUTSIDE,
|
||
};
|
||
#endif
|
||
|
||
REGISTER_DEVICES(device_table) = {
|
||
{ "pwm0", &pwm_dev_ops, (void *)&pwm_data0},
|
||
{ "pwm1", &pwm_dev_ops, (void *)&pwm_data1},
|
||
|
||
{ "iic0", &iic_dev_ops, (void *)&sw_iic0_data },
|
||
{ "iic1", &iic_dev_ops, (void *)&hw_iic1_data },
|
||
|
||
/*{ "audio", &audio_dev_ops, (void *)&audio_data },*/
|
||
|
||
#if TCFG_SD0_ENABLE
|
||
{ "sd0", &sd_dev_ops, (void *)&sd0_data },
|
||
#endif
|
||
|
||
#if TCFG_SD1_ENABLE
|
||
{ "sd1", &sd_dev_ops, (void *)&sd1_data },
|
||
#endif
|
||
|
||
#ifdef CONFIG_VIDEO_ENABLE
|
||
{ "video0.*", &video_dev_ops, (void *)&video0_data },
|
||
#endif
|
||
|
||
{ "spi1", &spi_dev_ops, (void *)&spi1_data },
|
||
{ "spi2", &spi_dev_ops, (void *)&spi2_data },
|
||
|
||
{"rtc", &rtc_dev_ops, NULL},
|
||
|
||
{"uart0", &uart_dev_ops, (void *)&uart0_data },
|
||
{"uart1", &uart_dev_ops, (void *)&uart1_data },
|
||
{"uart2", &uart_dev_ops, (void *)&uart2_data },
|
||
|
||
#if TCFG_USB_SLAVE_ENABLE || TCFG_USB_HOST_ENABLE
|
||
{ "otg", &usb_dev_ops, (void *)&otg_data},
|
||
#endif
|
||
};
|
||
|
||
|
||
/************************** LOW POWER config ****************************/
|
||
static const struct low_power_param power_param = {
|
||
.config = TCFG_LOWPOWER_LOWPOWER_SEL,
|
||
.btosc_disable = TCFG_LOWPOWER_BTOSC_DISABLE, //进入低功耗时BTOSC是否保持
|
||
.vddiom_lev = TCFG_LOWPOWER_VDDIOM_LEVEL, //强VDDIO等级,可选：2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.4V 3.6V
|
||
.vddiow_lev = TCFG_LOWPOWER_VDDIOW_LEVEL, //弱VDDIO等级,可选：2.1V 2.4V 2.8V 3.2V
|
||
.vdc14_dcdc = TRUE, //打开内部1.4VDCDC，关闭则用外部
|
||
.vdc14_lev = VDC14_VOL_SEL_LEVEL, //VDD1.4V配置
|
||
.sysvdd_lev = SYSVDD_VOL_SEL_LEVEL, //内核、sdram电压配置
|
||
.vlvd_enable = TRUE, //TRUE电压复位使能
|
||
.vlvd_value = VLVD_SEL_25V, //低电压复位电压值
|
||
};
|
||
|
||
/************************** PWR config ****************************/
|
||
//#define PORT_VCC33_CTRL_IO IO_PORTA_03 //VCC33 DCDC控制引脚,该引脚控制DCDC器件输出的3.3V连接芯片HPVDD、VDDIO、VDD33
|
||
#define PORT_WAKEUP_IO IO_PORTB_01 //软关机和休眠唤醒引脚
|
||
#define PORT_WAKEUP_NUM (PORT_WAKEUP_IO/IO_GROUP_NUM)//默认:0-7:GPIOA-GPIOH, 可以指定0-7组
|
||
|
||
static const struct port_wakeup port0 = {
|
||
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
|
||
.attribute = BLUETOOTH_RESUME, //保留参数
|
||
.iomap = PORT_WAKEUP_IO, //唤醒口选择
|
||
.low_power = POWER_SLEEP_WAKEUP|POWER_OFF_WAKEUP, //低功耗IO唤醒,不需要写0
|
||
};
|
||
|
||
static const struct long_press lpres_port = {
|
||
.enable = FALSE,
|
||
.use_sec4 = TRUE, //enable = TRUE , use_sec4: TRUE --> 4 sec , FALSE --> 8 sec
|
||
.edge = FALLING_EDGE, //长按方式,可选：FALLING_EDGE / RISING_EDGE --> 低电平/高电平
|
||
.iomap = PORT_WAKEUP_IO, //长按复位IO和IO唤醒共用一个IO
|
||
};
|
||
|
||
static const struct sub_wakeup sub_wkup = {
|
||
.attribute = BLUETOOTH_RESUME,
|
||
};
|
||
|
||
static const struct charge_wakeup charge_wkup = {
|
||
.attribute = BLUETOOTH_RESUME,
|
||
};
|
||
|
||
static const struct wakeup_param wk_param = {
|
||
.port[PORT_WAKEUP_NUM] = &port0,
|
||
.sub = &sub_wkup,
|
||
.charge = &charge_wkup,
|
||
.lpres = &lpres_port,
|
||
};
|
||
|
||
/*进软关机之前默认将IO口都设置成高阻状态，需要保留原来状态的请修改该函数*/
|
||
static void board_set_soft_poweroff(void)
|
||
{
|
||
u32 IO_PORT;
|
||
JL_PORT_FLASH_TypeDef *gpio[] = {JL_PORTA, JL_PORTB, JL_PORTC, JL_PORTD, JL_PORTE, JL_PORTF, JL_PORTG, JL_PORTH};
|
||
|
||
for (u8 p = 0; p < 8; ++p) {
|
||
//flash sdram PD PE PF PG口不能进行配置,由内部完成控制
|
||
if (gpio[p] == JL_PORTD || gpio[p] == JL_PORTE || gpio[p] == JL_PORTF || gpio[p] == JL_PORTG) {
|
||
continue;
|
||
}
|
||
for (u8 i = 0; i < 16; ++i) {
|
||
IO_PORT = IO_PORTA_00 + p * 16 + i;
|
||
gpio_set_pull_up(IO_PORT, 0);
|
||
gpio_set_pull_down(IO_PORT, 0);
|
||
gpio_set_direction(IO_PORT, 1);
|
||
gpio_set_die(IO_PORT, 0);
|
||
gpio_set_dieh(IO_PORT, 0);
|
||
gpio_set_hd(IO_PORT, 0);
|
||
gpio_set_hd1(IO_PORT, 0);
|
||
gpio_latch_en(IO_PORT, 1);
|
||
}
|
||
}
|
||
#ifdef PORT_VCC33_CTRL_IO
|
||
gpio_latch_en(PORT_VCC33_CTRL_IO, 0);
|
||
gpio_direction_output(PORT_VCC33_CTRL_IO, 0);
|
||
gpio_set_pull_up(PORT_VCC33_CTRL_IO, 0);
|
||
gpio_set_pull_down(PORT_VCC33_CTRL_IO, 1);
|
||
gpio_set_direction(PORT_VCC33_CTRL_IO, 1);
|
||
gpio_set_die(PORT_VCC33_CTRL_IO, 0);
|
||
gpio_set_dieh(PORT_VCC33_CTRL_IO, 0);
|
||
gpio_latch_en(PORT_VCC33_CTRL_IO, 1);
|
||
#endif
|
||
}
|
||
|
||
static void sleep_exit_callback(u32 usec)
|
||
{
|
||
#ifdef PORT_VCC33_CTRL_IO
|
||
gpio_direction_output(PORT_VCC33_CTRL_IO, 1);
|
||
gpio_set_pull_up(PORT_VCC33_CTRL_IO, 1);
|
||
gpio_set_pull_down(PORT_VCC33_CTRL_IO,0);
|
||
#endif
|
||
/* putchar('-'); */
|
||
}
|
||
|
||
static void sleep_enter_callback(u8 step)
|
||
{
|
||
/* 此函数禁止添加打印 */
|
||
|
||
if (step == 1) {
|
||
/*dac_power_off();*/
|
||
} else {
|
||
#ifdef PORT_VCC33_CTRL_IO
|
||
gpio_direction_output(PORT_VCC33_CTRL_IO, 0);
|
||
gpio_set_pull_up(PORT_VCC33_CTRL_IO, 0);
|
||
gpio_set_pull_down(PORT_VCC33_CTRL_IO, 1);
|
||
gpio_set_direction(PORT_VCC33_CTRL_IO, 1);
|
||
gpio_set_die(PORT_VCC33_CTRL_IO, 0);
|
||
#endif
|
||
}
|
||
}
|
||
|
||
static void board_power_init(void)
|
||
{
|
||
#ifdef PORT_VCC33_CTRL_IO
|
||
gpio_direction_output(PORT_VCC33_CTRL_IO, 1);
|
||
gpio_set_pull_up(PORT_VCC33_CTRL_IO, 1);
|
||
gpio_set_pull_down(PORT_VCC33_CTRL_IO,0);
|
||
#endif
|
||
|
||
power_init(&power_param);
|
||
|
||
power_set_callback(TCFG_LOWPOWER_LOWPOWER_SEL, sleep_enter_callback, sleep_exit_callback, board_set_soft_poweroff);
|
||
|
||
power_keep_state(POWER_KEEP_RESET);//0, POWER_KEEP_DACVDD | POWER_KEEP_RTC | POWER_KEEP_RESET
|
||
|
||
#ifdef CONFIG_RTC_ENABLE
|
||
power_keep_state(POWER_KEEP_RTC);//0, POWER_KEEP_DACVDD | POWER_KEEP_RTC | POWER_KEEP_RESET
|
||
#endif
|
||
|
||
power_wakeup_init(&wk_param);
|
||
}
|
||
|
||
#ifdef CONFIG_DEBUG_ENABLE
|
||
void debug_uart_init()
|
||
{
|
||
uart_init(&uart2_data);
|
||
}
|
||
#endif
|
||
|
||
void board_early_init()
|
||
{
|
||
devices_init();
|
||
}
|
||
|
||
void board_init()
|
||
{
|
||
board_power_init();
|
||
#ifdef CONFIG_RTC_ENABLE
|
||
rtc_early_init();
|
||
#endif
|
||
adc_init();
|
||
}
|
||
|