176 lines
4.8 KiB
C
176 lines
4.8 KiB
C
#include "app_config.h"
|
||
|
||
#include "system/includes.h"
|
||
#include "device/includes.h"
|
||
#include "asm/includes.h"
|
||
|
||
// *INDENT-OFF*
|
||
|
||
|
||
UART2_PLATFORM_DATA_BEGIN(uart2_data)
|
||
.baudrate = 115200,
|
||
.port = PORT_REMAP,
|
||
.output_channel = OUTPUT_CHANNEL0,
|
||
.tx_pin = IO_PORTC_03,
|
||
.rx_pin = -1,
|
||
.max_continue_recv_cnt = 1024,
|
||
.idle_sys_clk_cnt = 500000,
|
||
.clk_src = PLL_48M,
|
||
.flags = UART_DEBUG,
|
||
UART2_PLATFORM_DATA_END();
|
||
|
||
|
||
#if TCFG_ADKEY_ENABLE
|
||
|
||
#define ADKEY_UPLOAD_R 22
|
||
|
||
#define ADC_VDDIO (0x3FF)
|
||
#define ADC_09 (0x3FF)
|
||
#define ADC_08 (0x3FF)
|
||
#define ADC_07 (0x3FF)
|
||
#define ADC_06 (0x3FF)
|
||
#define ADC_05 (0x3FF)
|
||
#define ADC_04 (0x3FF)
|
||
#define ADC_03 (0x3FF * 15 / (15 + ADKEY_UPLOAD_R))
|
||
#define ADC_02 (0x3FF * 10 / (10 + ADKEY_UPLOAD_R))
|
||
#define ADC_01 (0x3FF * 33 / (33 + ADKEY_UPLOAD_R * 10))
|
||
#define ADC_00 (0)
|
||
|
||
#define ADKEY_V_9 ((ADC_09 + ADC_VDDIO)/2)
|
||
#define ADKEY_V_8 ((ADC_08 + ADC_09)/2)
|
||
#define ADKEY_V_7 ((ADC_07 + ADC_08)/2)
|
||
#define ADKEY_V_6 ((ADC_06 + ADC_07)/2)
|
||
#define ADKEY_V_5 ((ADC_05 + ADC_06)/2)
|
||
#define ADKEY_V_4 ((ADC_04 + ADC_05)/2)
|
||
#define ADKEY_V_3 ((ADC_03 + ADC_04)/2)
|
||
#define ADKEY_V_2 ((ADC_02 + ADC_03)/2)
|
||
#define ADKEY_V_1 ((ADC_01 + ADC_02)/2)
|
||
#define ADKEY_V_0 ((ADC_00 + ADC_01)/2)
|
||
|
||
const struct adkey_platform_data adkey_data = {
|
||
.enable = 1,
|
||
.adkey_pin = IO_PORTB_01,
|
||
.extern_up_en = 1,
|
||
.ad_channel = 3,
|
||
.ad_value = {
|
||
ADKEY_V_0,
|
||
ADKEY_V_1,
|
||
ADKEY_V_2,
|
||
ADKEY_V_3,
|
||
ADKEY_V_4,
|
||
ADKEY_V_5,
|
||
ADKEY_V_6,
|
||
ADKEY_V_7,
|
||
ADKEY_V_8,
|
||
ADKEY_V_9,
|
||
},
|
||
.key_value = {
|
||
0,
|
||
1,
|
||
3,
|
||
2,
|
||
NO_KEY,
|
||
NO_KEY,
|
||
NO_KEY,
|
||
NO_KEY,
|
||
NO_KEY,
|
||
NO_KEY,
|
||
},
|
||
};
|
||
|
||
#endif
|
||
|
||
|
||
/************************** LOW POWER config ****************************/
|
||
static const struct low_power_param power_param = {
|
||
.config = TCFG_LOWPOWER_LOWPOWER_SEL,
|
||
.btosc_disable = TCFG_LOWPOWER_BTOSC_DISABLE, //进入低功耗时BTOSC是否保持
|
||
.vddiom_lev = TCFG_LOWPOWER_VDDIOM_LEVEL, //强VDDIO等级,可选：2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.4V 3.6V
|
||
.vddiow_lev = TCFG_LOWPOWER_VDDIOW_LEVEL, //弱VDDIO等级,可选：2.1V 2.4V 2.8V 3.2V
|
||
.vdc14_dcdc = TRUE, //打开内部1.4VDCDC，关闭则用外部
|
||
.vdc14_lev = VDC14_VOL_SEL_LEVEL, //VDD1.4V配置
|
||
.sysvdd_lev = SYSVDD_VOL_SEL_LEVEL, //内核、sdram电压配置
|
||
.vlvd_enable = TRUE, //TRUE电压复位使能
|
||
.vlvd_value = VLVD_SEL_25V, //低电压复位电压值
|
||
};
|
||
|
||
/************************** PWR config ****************************/
|
||
#define PORT_WAKEUP_IO IO_PORTB_01 //软关机和休眠唤醒引脚
|
||
#define PORT_WAKEUP_NUM (PORT_WAKEUP_IO/IO_GROUP_NUM)//默认:0-7:GPIOA-GPIOH, 可以指定0-7组
|
||
|
||
static const struct port_wakeup port0 = {
|
||
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
|
||
.attribute = BLUETOOTH_RESUME, //保留参数
|
||
.iomap = PORT_WAKEUP_IO, //唤醒口选择
|
||
.low_power = POWER_SLEEP_WAKEUP|POWER_OFF_WAKEUP, //低功耗IO唤醒,不需要写0
|
||
};
|
||
|
||
static const struct long_press lpres_port = {
|
||
.enable = FALSE,
|
||
.use_sec4 = TRUE, //enable = TRUE , use_sec4: TRUE --> 4 sec , FALSE --> 8 sec
|
||
.edge = FALLING_EDGE, //长按方式,可选：FALLING_EDGE / RISING_EDGE --> 低电平/高电平
|
||
.iomap = PORT_WAKEUP_IO, //长按复位IO和IO唤醒共用一个IO
|
||
};
|
||
|
||
static const struct sub_wakeup sub_wkup = {
|
||
.attribute = BLUETOOTH_RESUME,
|
||
};
|
||
|
||
static const struct charge_wakeup charge_wkup = {
|
||
.attribute = BLUETOOTH_RESUME,
|
||
};
|
||
|
||
static const struct wakeup_param wk_param = {
|
||
.port[PORT_WAKEUP_NUM] = &port0,
|
||
.sub = &sub_wkup,
|
||
.charge = &charge_wkup,
|
||
.lpres = &lpres_port,
|
||
};
|
||
|
||
|
||
#if defined CONFIG_BT_ENABLE || defined CONFIG_WIFI_ENABLE
|
||
#include "wifi/wifi_connect.h"
|
||
const struct wifi_calibration_param wifi_calibration_param = {
|
||
.xosc_l = 0xb,// 调节晶振左电容
|
||
.xosc_r = 0xb,// 调节晶振右电容
|
||
.pa_trim_data ={1, 7, 4, 7, 11, 1, 7},// 根据MP测试生成PA TRIM值
|
||
};
|
||
#endif
|
||
|
||
REGISTER_DEVICES(device_table) = {
|
||
{"uart2", &uart_dev_ops, (void *)&uart2_data },
|
||
};
|
||
|
||
#ifdef CONFIG_DEBUG_ENABLE
|
||
void debug_uart_init()
|
||
{
|
||
uart_init(&uart2_data);
|
||
}
|
||
#endif
|
||
|
||
void board_early_init()
|
||
{
|
||
devices_init();
|
||
}
|
||
|
||
static void board_power_init(void)
|
||
{
|
||
power_init(&power_param);
|
||
|
||
power_keep_state(POWER_KEEP_RESET);
|
||
|
||
power_wakeup_init(&wk_param);
|
||
}
|
||
|
||
void board_init()
|
||
{
|
||
board_power_init();
|
||
adc_init();
|
||
#if TCFG_ADKEY_ENABLE
|
||
key_driver_init();
|
||
#endif
|
||
void cfg_file_parse(void);
|
||
cfg_file_parse();
|
||
}
|
||
|