/* * 航拍板 */ #include "app_config.h" #ifdef CONFIG_BOARD_DEVELOP #include "app_power_manage.h" #include "system/includes.h" #include "device/includes.h" #include "device/iic.h" #include "server/audio_dev.h" #include "asm/includes.h" #if (TCFG_IOKEY_ENABLE || TCFG_IRKEY_ENABLE || TCFG_RDEC_KEY_ENABLE || TCFG_ADKEY_ENABLE) #include "key/iokey.h" #include "key/adkey.h" #include "key/irkey.h" #include "key/rdec_key.h" #include "key/key_driver.h" #include "event/key_event.h" #endif #if TCFG_USB_SLAVE_ENABLE || TCFG_USB_HOST_ENABLE #include "otg.h" #include "usb_host.h" #include "usb_common_def.h" #include "usb_storage.h" #include "asm/uvc_device.h" #endif #ifdef CONFIG_UI_ENABLE #include "lcd_drive.h" #include "ui_api.h" #endif #ifdef CONFIG_LTE_PHY_ENABLE #include "lte_module.h" #endif // *INDENT-OFF* #define DEBUG_IO TCFG_DEBUG_PORT UART0_PLATFORM_DATA_BEGIN(uart0_data) .baudrate = 1000000, .port = PORT_REMAP, .output_channel = OUTPUT_CHANNEL0, .input_channel = INPUT_CHANNEL0, .tx_pin = DEBUG_IO, .rx_pin = -1, .max_continue_recv_cnt = 1024, .idle_sys_clk_cnt = 500000, .clk_src = PLL_48M, .flags = UART_DEBUG, UART0_PLATFORM_DATA_END(); UART1_PLATFORM_DATA_BEGIN(uart1_data) .baudrate = 1000000, .port = PORT_REMAP, /* .port = PORTH_6_7, */ /* .port = PORTC_3_4, */ /* .port = PORTUSB_B, */ /* .port = PORTUSB_A, */ /* .tx_pin = IO_PORTH_06, */ /* .rx_pin = IO_PORTH_07, */ /* .tx_pin = IO_PORTC_03, */ /* .rx_pin = IO_PORTC_04, */ /* .tx_pin = IO_PORT_USB_DPB, */ /* .rx_pin = IO_PORT_USB_DMB, */ /* .tx_pin = IO_PORT_USB_DPA, */ /* .rx_pin = IO_PORT_USB_DMA, */ .tx_pin = IO_PORTB_00, .rx_pin = IO_PORTB_01, .output_channel = OUTPUT_CHANNEL3, .input_channel = INPUT_CHANNEL3, .max_continue_recv_cnt = 1024, .idle_sys_clk_cnt = 500000, .clk_src = PLL_48M, .flags = UART_DEBUG, UART1_PLATFORM_DATA_END(); UART2_PLATFORM_DATA_BEGIN(uart2_data) .baudrate = 1000000, /*.tx_pin = IO_PORTH_02,*/ /*.rx_pin = IO_PORTH_03,*/ .port = PORT_REMAP, .tx_pin = DEBUG_IO, .rx_pin = -1, /* .tx_pin = IO_PORTC_09, */ /* .rx_pin = IO_PORTC_10, */ /* .tx_pin = IO_PORTB_06, */ /* .rx_pin = IO_PORTB_07, */ /* .tx_pin = IO_PORTE_00,*/ /* .rx_pin = IO_PORTE_01,*/ .output_channel = OUTPUT_CHANNEL2, .input_channel = INPUT_CHANNEL2, .max_continue_recv_cnt = 1024, .idle_sys_clk_cnt = 500000, .clk_src = PLL_48M, .flags = UART_DEBUG, UART2_PLATFORM_DATA_END(); /****************SD模块********************************************************** * 暂只支持1个SD外设，如需要多个SD外设，自行去掉下面SD0/1_ENABLE控制，另外定义即可 ********************************************************************************/ #if (TCFG_SD0_ENABLE || TCFG_SD1_ENABLE) #if TCFG_SD0_ENABLE //sd0 #define SD_PLATFORM_DATA_BEGIN() SD0_PLATFORM_DATA_BEGIN(sd0_data) #define SD_PLATFORM_DATA_END() SD0_PLATFORM_DATA_END() #define SD_CLK_DETECT_FUNC sdmmc_0_clk_detect #elif TCFG_SD1_ENABLE //sd1 #define SD_PLATFORM_DATA_BEGIN() SD1_PLATFORM_DATA_BEGIN(sd1_data) #define SD_PLATFORM_DATA_END() SD1_PLATFORM_DATA_END() #define SD_CLK_DETECT_FUNC sdmmc_1_clk_detect #endif SD_PLATFORM_DATA_BEGIN() .port = TCFG_SD_PORTS, .priority = 3, .data_width = TCFG_SD_DAT_WIDTH, .speed = TCFG_SD_CLK, .detect_mode = TCFG_SD_DET_MODE, #if (TCFG_SD_DET_MODE == SD_CLK_DECT) .detect_func = SD_CLK_DETECT_FUNC, #elif (TCFG_SD_DET_MODE == SD_IO_DECT) .detect_func = sdmmc_0_io_detect, #else .detect_func = NULL, #endif .power = NULL,//sd_set_power, SD_PLATFORM_DATA_END() #endif /****************SD模块*********************/ HW_IIC0_PLATFORM_DATA_BEGIN(hw_iic1_data) /* .clk_pin = IO_PORTC_01, */ /* .dat_pin = IO_PORTC_02, */ .clk_pin = IO_PORTH_00, .dat_pin = IO_PORTH_01, .baudrate = 0x3f,//3f:385k HW_IIC0_PLATFORM_DATA_END() SW_IIC_PLATFORM_DATA_BEGIN(sw_iic0_data) .clk_pin = TCFG_IIC0_CLK, .dat_pin = TCFG_IIC0_DAT, .sw_iic_delay = 50, SW_IIC_PLATFORM_DATA_END() #ifdef CONFIG_VIDEO1_ENABLE SW_IIC_PLATFORM_DATA_BEGIN(sw_iic1_data) .clk_pin = TCFG_IIC1_CLK, .dat_pin = TCFG_IIC1_DAT, .sw_iic_delay = 50, SW_IIC_PLATFORM_DATA_END() #endif #if TCFG_ADKEY_ENABLE /*-------------ADKEY GROUP 1----------------*/ #define ADKEY_UPLOAD_R 22 #define ADC_VDDIO (0x3FF) #define ADC_09 (0x3FF * 220 / (220 + ADKEY_UPLOAD_R)) #define ADC_08 (0x3FF * 120 / (120 + ADKEY_UPLOAD_R)) #define ADC_07 (0x3FF * 51 / (51 + ADKEY_UPLOAD_R)) #define ADC_06 (0x3FF * 33 / (33 + ADKEY_UPLOAD_R)) #define ADC_05 (0x3FF * 22 / (22 + ADKEY_UPLOAD_R)) #define ADC_04 (0x3FF * 15 / (15 + ADKEY_UPLOAD_R)) #define ADC_03 (0x3FF * 10 / (10 + ADKEY_UPLOAD_R)) #define ADC_02 (0x3FF * 62 / (62 + ADKEY_UPLOAD_R * 10)) #define ADC_01 (0x3FF * 3 / ( 3 + ADKEY_UPLOAD_R)) #define ADC_00 (0) #define ADKEY_V_9 ((ADC_09 + ADC_VDDIO)/2) #define ADKEY_V_8 ((ADC_08 + ADC_09)/2) #define ADKEY_V_7 ((ADC_07 + ADC_08)/2) #define ADKEY_V_6 ((ADC_06 + ADC_07)/2) #define ADKEY_V_5 ((ADC_05 + ADC_06)/2) #define ADKEY_V_4 ((ADC_04 + ADC_05)/2) #define ADKEY_V_3 ((ADC_03 + ADC_04)/2) #define ADKEY_V_2 ((ADC_02 + ADC_03)/2) #define ADKEY_V_1 ((ADC_01 + ADC_02)/2) #define ADKEY_V_0 ((ADC_00 + ADC_01)/2) const struct adkey_platform_data adkey_data = {//按键不需要添加到设备列表 .enable = 1, .adkey_pin = IO_PORTB_01, .extern_up_en = 1, .ad_channel = 3, .ad_value = { ADKEY_V_0, ADKEY_V_1, ADKEY_V_2, ADKEY_V_3, ADKEY_V_4, ADKEY_V_5, ADKEY_V_6, ADKEY_V_7, ADKEY_V_8, ADKEY_V_9, }, .key_value = { KEY_MENU, /*0*/ KEY_PHOTO, /*1*/ KEY_ENC, /*2*/ KEY_F1, /*3*/ KEY_MODE, /*4*/ KEY_CANCLE,/*5*/ KEY_OK, /*6*/ KEY_DOWN, /*7*/ KEY_UP, /*8*/ NO_KEY, }, }; #endif #if TCFG_IOKEY_ENABLE static const struct iokey_port iokey_list[] = { { .connect_way = ONE_PORT_TO_LOW, //IO按键的连接方式 .key_type.one_io.port = IO_PORTB_01, //IO按键对应的引脚 .key_value = KEY_MENU, //按键值 } }; const struct iokey_platform_data iokey_data = {//按键不需要添加到设备列表 .enable = 1, //是否使能IO按键 .num = ARRAY_SIZE(iokey_list), //IO按键的个数 .port = iokey_list, //IO按键参数表 }; #endif #if TCFG_RDEC_KEY_ENABLE const struct rdec_device rdeckey_list[] = { { .index = RDEC0 , .sin_port0 = IO_PORTC_09, .sin_port1 = IO_PORTC_10, .key_value0 = KEY_VOLUME_DEC | BIT(7), .key_value1 = KEY_VOLUME_INC | BIT(7), }, }; const struct rdec_platform_data rdec_key_data = {//按键不需要添加到设备列表 .enable = 1, .num = ARRAY_SIZE(rdeckey_list), //RDEC按键的个数 .rdec = rdeckey_list, //RDEC按键参数表 }; #endif /* * spi0接falsh */ SPI0_PLATFORM_DATA_BEGIN(spi0_data) .clk = 20000000, .mode = SPI_STD_MODE, .port = 'A', SPI0_PLATFORM_DATA_END() SPI1_PLATFORM_DATA_BEGIN(spi1_data) .clk = 80000000, .mode = SPI_STD_MODE, .attr = SPI_SCLK_L_UPH_SMPH | SPI_BIDIR_MODE, .port = 'B', SPI1_PLATFORM_DATA_END() SPI2_PLATFORM_DATA_BEGIN(spi2_data) .clk = 80000000, #ifdef CONFIG_SPI_VIDEO_ENABLE //=======SPI接收摄像头数据 #if !CONFIG_SPI_VIDEO_USE_ISC1_RECV #if CONFIG_SPI_ONE_LINE_ENABLE .mode = SPI_1WIRE_MODE,//单线 #else .mode = SPI_DUAL_MODE,//双线 #endif .port = 'C', .attr = TCFG_SPI_ATTR,//主从机、边缘极性采样 #endif //=======SPI接收摄像头数据 #else .mode = SPI_STD_MODE, .attr = SPI_SCLK_L_UPH_SMPH | SPI_BIDIR_MODE, .port = 'A', #endif SPI2_PLATFORM_DATA_END() static const struct spiflash_platform_data spiflash_data = { .name = "spi0", .mode = FAST_READ_OUTPUT_MODE,//FAST_READ_IO_MODE, .sfc_run_mode = SFC_FAST_READ_DUAL_OUTPUT_MODE, }; #ifdef CONFIG_UI_ENABLE #if TCFG_LCD_ILI9341_ENABLE #define EMI_BAUD_DIV EMI_BAUD_DIV6 #else #define EMI_BAUD_DIV EMI_BAUD_DIV8 #endif static const struct emi_platform_data emi_data = { .bits_mode = EMI_8BITS_MODE, .baudrate = EMI_BAUD_DIV, //clock = HSB_CLK / (baudrate + 1) , HSB分频 .colection = EMI_FALLING_COLT, //EMI_FALLING_COLT / EMI_RISING_COLT : 下降沿 上升沿 采集数据 .time_out = 1*1000, //最大写超时时间ms .th = EMI_TWIDTH_NO_HALF, .ts = 0, #if TCFG_LCD_ILI9481_ENABLE .tw = EMI_BAUD_DIV5, #else .tw = (EMI_BAUD_DIV > 1) ? EMI_BAUD_DIV / 2 : 1, #endif .data_bit_en = 0, //0默认根据bits_mode数据位来配置 }; static const struct pap_info pap_data = { .datawidth = PAP_PORT_8BITS, .endian = PAP_BE, //数据输出大小端 .cycle = PAP_CYCLE_ONE, //1/2字节发送次数 .pre = PAP_READ_LOW, //读取rd有效电平 .pwe = PAP_WRITE_LOW, //写wr有效电平 .use_sem = TRUE, //使用信号等待 .rd_en = FALSE, //不使用rd读信号 .port_sel = PAP_PORT_A, //PAP_PORT_A PAP_PORT_B .timing_setup = 1, //具体看pap.h .timing_hold = 1, //具体看pap.h .timing_width = 2, //具体看pap.h }; #if TCFG_LCD_ST7735S_ENABLE || TCFG_LCD_ST7789V_ENABLE SPI2_PLATFORM_DATA_BEGIN(spi2_data) //pc8 pc9 pc10 .clk = 80000000, //di clk do .mode = SPI_1WIRE_MODE, .port = 'A', .attr = SPI_SCLK_L_UPL_SMPH | SPI_UNIDIR_MODE,//主机，CLK低 更新数据低，单向模式 SPI2_PLATFORM_DATA_END() #endif static const struct ui_lcd_platform_data pdata = { #if TCFG_LCD_ST7735S_ENABLE || TCFG_LCD_ST7789V_ENABLE .spi_id = "spi2", .rs_pin = IO_PORTH_02, .te_pin = IO_PORTH_03, .rst_pin = IO_PORTH_04, .cs_pin = IO_PORTH_07, .lcd_if = LCD_SPI,//屏幕接口类型还有 PAP , SPI #endif #if TCFG_LCD_ST7789S_ENABLE .rs_pin = IO_PORTH_02, .te_pin = IO_PORTH_03, .rst_pin = IO_PORTH_04, .cs_pin = IO_PORTH_07, .lcd_if = LCD_EMI,//屏幕接口类型还有 PAP , SPI #endif #if TCFG_LCD_ILI9341_ENABLE || TCFG_LCD_ILI9481_ENABLE .rs_pin = IO_PORTC_09, .te_pin = IO_PORTC_00, .bl_pin = IO_PORTB_08, .touch_int_pin = IO_PORTB_04, .touch_reset_pin = IO_PORTB_00, .cs_pin = -1, .rst_pin = -1, .lcd_if = LCD_EMI,//屏幕接口类型还有 PAP , SPI #endif #if TCFG_LCD_480x272_8BITS /*RGB*/ .lcd_if = LCD_IMD, #endif }; const struct ui_devices_cfg ui_cfg_data = { .type = TFT_LCD, .private_data = (void *)&pdata, }; #endif static const struct dac_platform_data dac_data = { .sw_differ = 0, .pa_auto_mute = 1, .pa_mute_port = TCFG_DAC_MUTE_PORT, .pa_mute_value = TCFG_DAC_MUTE_VALUE, .differ_output = 0, .hw_channel = 0x05, .ch_num = 4, .vcm_init_delay_ms = 1000, .mute_delay_ms = 200, #ifdef CONFIG_DEC_ANALOG_VOLUME_ENABLE .fade_enable = 1, .fade_delay_ms = 40, #endif }; static const struct adc_platform_data adc_data = { #ifdef CONFIG_ALL_ADC_CHANNEL_OPEN_ENABLE .mic_channel = TCFG_MIC_CHANNEL_MAP, .linein_channel = TCFG_LINEIN_CHANNEL_MAP, .mic_ch_num = TCFG_MIC_CHANNEL_NUM, .linein_ch_num = TCFG_LINEIN_CHANNEL_NUM, .all_channel_open = 1, #else .mic_channel = LADC_CH_MIC1_P_N, .mic_ch_num = 1, #endif .isel = 2, .dump_num = 480, }; static const struct audio_pf_data audio_pf_d = { .adc_pf_data = &adc_data, .dac_pf_data = &dac_data, }; static const struct audio_platform_data audio_data = { .private_data = (void *) &audio_pf_d, }; #ifdef CONFIG_VIDEO_ENABLE /* #define CAMERA_GROUP_PORT ISC_GROUPA */ /* #define CAMERA_GROUP_PORT ISC_GROUPC */ static const struct camera_platform_data camera0_data = { .xclk_gpio = TCFG_VIDEO0_CAMERA_XCLOCK,//注意： 如果硬件xclk接到芯片IO，则会占用OUTPUT_CHANNEL1 .reset_gpio = TCFG_VIDEO0_CAMERA_RESET, .reset_gpio = TCFG_VIDEO0_CAMERA_RESET, .pwdn_gpio = TCFG_VIDEO0_CAMERA_PWDN, .online_detect = NULL, .power_value = 0, .interface = SEN_INTERFACE0,//SEN_INTERFACE_CSI2, .dvp={ #if (CAMERA_GROUP_PORT == ISC_GROUPA) .pclk_gpio = IO_PORTA_08, .hsync_gpio = IO_PORTA_09, .vsync_gpio = IO_PORTA_10, #else .pclk_gpio = IO_PORTC_08, .hsync_gpio = IO_PORTC_09, .vsync_gpio = IO_PORTC_10, #endif .group_port = CAMERA_GROUP_PORT, .data_gpio={ #if (CAMERA_GROUP_PORT == ISC_GROUPA) IO_PORTA_07, IO_PORTA_06, IO_PORTA_05, IO_PORTA_04, IO_PORTA_03, IO_PORTA_02, IO_PORTA_01, IO_PORTA_00, -1, -1, #else IO_PORTC_07, IO_PORTC_06, IO_PORTC_05, IO_PORTC_04, IO_PORTC_03, IO_PORTC_02, IO_PORTC_01, IO_PORTC_00, -1, -1, #endif }, } }; static const struct video_subdevice_data video0_subdev_data[] = { { VIDEO_TAG_CAMERA, (void *)&camera0_data }, }; static const struct video_platform_data video0_data = { .data = video0_subdev_data, .num = ARRAY_SIZE(video0_subdev_data), }; #endif #ifdef CONFIG_VIDEO1_ENABLE static const struct camera_platform_data camera1_data = { .xclk_gpio = TCFG_VIDEO1_CAMERA_XCLOCK,//IO_PORTB_02,//IO_PORTC_08,//IO_PORTC_06,//注意： 如果硬件xclk接到芯片IO，则会占用OUTPUT_CHANNEL1 .reset_gpio = TCFG_VIDEO1_CAMERA_RESET, .online_detect = NULL, .pwdn_gpio = TCFG_VIDEO1_CAMERA_PWDN, .power_value = 0, .interface = SEN_INTERFACE0, .dvp={ .group_port = CAMERA1_GROUP_PORT, #if (CAMERA1_GROUP_PORT == ISC_GROUPC) .pclk_gpio = IO_PORTC_08, #elif (CAMERA1_GROUP_PORT == ISC_GROUPH) .pclk_gpio = IO_PORTH_04, #endif .hsync_gpio = -1, .vsync_gpio = -1, .data_gpio={ #if (CAMERA1_GROUP_PORT == ISC_GROUPC) IO_PORTC_00, #elif (CAMERA1_GROUP_PORT == ISC_GROUPH) IO_PORTH_03, #endif -1, -1, -1, -1, -1, -1, -1, -1, -1 }, } }; static const struct video_subdevice_data video1_subdev_data[] = { { VIDEO_TAG_CAMERA, (void *)&camera1_data }, }; static const struct video_platform_data video1_data = { .data = video1_subdev_data, .num = ARRAY_SIZE(video1_subdev_data), }; #endif LED_PLATFORM_DATA_BEGIN(pwm_led_data) .led_pin = IO_PORTB_00, .led_cfg.led0_bright = 2, //1 ~ 4, value越大, (红灯)亮度越高 .led_cfg.led1_bright = 2, //1 ~ 4, value越大, (蓝灯)亮度越高 .led_cfg.single_led_slow_freq = 3, //1 ~ 8, value越大, LED单独慢闪速度越慢, value * 0.5s闪烁一次 .led_cfg.single_led_fast_freq = 3, //1 ~ 4, value越大, LED单独快闪速度越慢, value * 100ms闪烁一次 .led_cfg.double_led_slow_freq = 3, //1 ~ 8, value越大, LED交替慢闪速度越慢, value * 0.5s闪烁一次 .led_cfg.double_led_fast_freq = 3, //1 ~ 4, value越大, LED交替快闪速度越慢, value * 100ms闪烁一次 LED_PLATFORM_DATA_END() PWM_PLATFORM_DATA_BEGIN(pwm_data0) .port = 0, .pwm_ch = PWMCH0_H | PWMCH0_L,//初始化可选多通道,如:PWMCH0_H | PWMCH0_L | PWMCH1_H ... | PWMCH7_H | PWMCH7_L | PWM_TIMER2_OPCH2 | PWM_TIMER3_OPCH3 , .freq = 1000,//频率 .duty = 50,//占空比 .point_bit = 0,//根据point_bit值调节占空比小数点精度位: 040K,point_bit=0; PWM_PLATFORM_DATA_END() PWM_PLATFORM_DATA_BEGIN(pwm_data1) .port = IO_PORTA_03,//选择定时器的TIMER PWM任意IO，pwm_ch加上PWM_TIMER3_OPCH3或PWM_TIMER2_OPCH2有效,只支持2个PWM,占用output_channel2/3，其他外设使用output_channel需留意 .pwm_ch = PWM_TIMER2_OPCH2,//初始化可选多通道,如:PWMCH0_H | PWMCH0_L | PWMCH1_H ... | PWMCH7_H | PWMCH7_L | PWM_TIMER2_OPCH2 | PWM_TIMER3_OPCH3 , .freq = 1000,//频率 .duty = 50,//占空比 .point_bit = 0,//根据point_bit值调节占空比小数点精度位: 040K,point_bit=0; PWM_PLATFORM_DATA_END() #if TCFG_USB_SLAVE_ENABLE || TCFG_USB_HOST_ENABLE static const struct otg_dev_data otg_data = { .usb_dev_en = (TCFG_HUSB_EN << 1) | TCFG_FUSB_EN, #if TCFG_USB_SLAVE_ENABLE .slave_online_cnt = 10, .slave_offline_cnt = 10, #endif #if TCFG_USB_HOST_ENABLE .host_online_cnt = 10, .host_offline_cnt = 10, #endif .detect_mode = OTG_HOST_MODE | OTG_SLAVE_MODE | OTG_CHARGE_MODE, .detect_time_interval = 50, }; #endif #ifdef CONFIG_LTE_PHY_ENABLE extern const struct device_operations lte_module_dev_ops; LTE_MODULE_DATA_BEGIN(lte_module_data) .name = (u8 *)"usb_rndis", LTE_MODULE_DATA_END() #endif #if defined CONFIG_BT_ENABLE || defined CONFIG_WIFI_ENABLE #include "wifi/wifi_connect.h" const struct wifi_calibration_param wifi_calibration_param = { .xosc_l = 0xb,// 调节左晶振电容 .xosc_r = 0xb,// 调节右晶振电容 .pa_trim_data ={1, 7, 4, 7, 11, 1, 7},// 根据MP测试生成PA TRIM值 .mcs_dgain ={ 50,//11B_1M 50,//11B_2.2M 50,//11B_5.5M 50,//11B_11M 72,//11G_6M 72,//11G_9M 85,//11G_12M 80,//11G_18M 64,//11G_24M 64,//11G_36M 62,//11G_48M 52,//11G_54M 72,//11N_MCS0 90,//11N_MCS1 80,//11N_MCS2 64,//11N_MCS3 64,//11N_MCS4 64,//11N_MCS5 50,//11N_MCS6 43,//11N_MCS7 } }; #endif #ifdef CONFIG_RTC_ENABLE const struct rtc_init_config rtc_init_data = { .rtc_clk_sel = RTC_CLK_SEL_INSIDE, .rtc_power_sel = RTCVDD_SUPPLY_OUTSIDE, }; #endif REGISTER_DEVICES(device_table) = { #ifdef CONFIG_UI_ENABLE { "pap", &pap_dev_ops, (void *)&pap_data}, { "emi", &emi_dev_ops, (void *)&emi_data}, { "imd", &imd_dev_ops, NULL}, #endif { "pwm0", &pwm_dev_ops, (void *)&pwm_data0}, { "pwm1", &pwm_dev_ops, (void *)&pwm_data1}, { "iic0", &iic_dev_ops, (void *)&sw_iic0_data }, #ifdef CONFIG_VIDEO1_ENABLE { "iic1", &iic_dev_ops, (void *)&sw_iic1_data }, { "iic2", &iic_dev_ops, (void *)&hw_iic1_data }, #else { "iic1", &iic_dev_ops, (void *)&hw_iic1_data }, #endif { "audio", &audio_dev_ops, (void *)&audio_data }, #if TCFG_SD0_ENABLE { "sd0", &sd_dev_ops, (void *)&sd0_data }, #endif #if TCFG_SD1_ENABLE { "sd1", &sd_dev_ops, (void *)&sd1_data }, #endif #ifdef CONFIG_VIDEO_ENABLE { "video0.*", &video_dev_ops, (void *)&video0_data }, #endif #ifdef CONFIG_VIDEO1_ENABLE { "video1.*", &video_dev_ops, (void *)&video1_data },//vdieo1为spi摄像头 { "video3.*", &video_dev_ops, (void *)&video1_data },//video3为双路(jpeg+yuv)dvp摄像头 #endif #ifdef CONFIG_VIDEO_DEC_ENABLE { "video_dec", &video_dev_ops, NULL }, #endif #ifdef CONFIG_UVC_VIDEO2_ENABLE {"uvc", &uvc_dev_ops, NULL}, { "video2.*", &video_dev_ops, NULL }, #endif { "spi1", &spi_dev_ops, (void *)&spi1_data }, { "spi2", &spi_dev_ops, (void *)&spi2_data }, {"rtc", &rtc_dev_ops, NULL}, {"uart0", &uart_dev_ops, (void *)&uart0_data }, {"uart1", &uart_dev_ops, (void *)&uart1_data }, {"uart2", &uart_dev_ops, (void *)&uart2_data }, #if TCFG_USB_SLAVE_ENABLE || TCFG_USB_HOST_ENABLE { "otg", &usb_dev_ops, (void *)&otg_data}, #endif #if TCFG_UDISK_ENABLE { "udisk0", &mass_storage_ops, NULL }, { "udisk1", &mass_storage_ops, NULL }, #endif #ifdef CONFIG_LTE_PHY_ENABLE { "lte", <e_module_dev_ops, (void *) <e_module_data}, #endif }; /************************** LOW POWER config ****************************/ static const struct low_power_param power_param = { .config = TCFG_LOWPOWER_LOWPOWER_SEL, //系统休眠 .btosc_disable = TCFG_LOWPOWER_BTOSC_DISABLE, //进入低功耗时BTOSC是否保持 .vddiom_lev = TCFG_LOWPOWER_VDDIOM_LEVEL, //强VDDIO等级,可选：2.8V 2.9V 3.0V 3.1V 3.2V 3.3V 3.4V 3.5V .vddiow_lev = TCFG_LOWPOWER_VDDIOW_LEVEL, //弱VDDIO等级,可选：2.1V 2.4V 2.8V 3.2V .vdc14_dcdc = TRUE, //打开内部1.4VDCDC，关闭则用外部 .vdc14_lev = VDC14_VOL_SEL_LEVEL, //VDD1.4V配置 .sysvdd_lev = SYSVDD_VOL_SEL_LEVEL, //内核、sdram电压配置 .vlvd_enable = TRUE, //TRUE电压复位使能 .vlvd_value = VLVD_SEL_25V, //低电压复位电压值 }; /************************** PWR config ****************************/ //#define PORT_VCC33_CTRL_IO IO_PORTA_03 //VCC33 DCDC控制引脚,该引脚控制DCDC器件输出的3.3V连接芯片HPVDD、VDDIO、VDD33 #define PORT_WAKEUP_IO IO_PORTB_01 //软关机和休眠唤醒引脚 #define PORT_WAKEUP_NUM (PORT_WAKEUP_IO/IO_GROUP_NUM)//默认:0-7:GPIOA-GPIOH, 可以指定0-7组 static const struct port_wakeup port0 = { .edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿 .attribute = BLUETOOTH_RESUME, //保留参数 .iomap = PORT_WAKEUP_IO, //唤醒口选择 .low_power = POWER_SLEEP_WAKEUP|POWER_OFF_WAKEUP, //低功耗IO唤醒,不需要写0 }; static const struct long_press lpres_port = { .enable = FALSE, .use_sec4 = TRUE, //enable = TRUE , use_sec4: TRUE --> 4 sec , FALSE --> 8 sec .edge = FALLING_EDGE, //长按方式,可选：FALLING_EDGE / RISING_EDGE --> 低电平/高电平 .iomap = PORT_WAKEUP_IO, //长按复位IO和IO唤醒共用一个IO }; static const struct sub_wakeup sub_wkup = { .attribute = BLUETOOTH_RESUME, }; static const struct charge_wakeup charge_wkup = { .attribute = BLUETOOTH_RESUME, }; static const struct wakeup_param wk_param = { .port[PORT_WAKEUP_NUM] = &port0, .sub = &sub_wkup, .charge = &charge_wkup, .lpres = &lpres_port, }; unsigned char PWR_CTL(unsigned char on_off) { return 0; } #define USB_WKUP_IO 0//IO_PORT_PR_01 unsigned char usb_is_charging() { #if 0 static unsigned char init = 0; if (!init) { init = 1; gpio_latch_en(USB_WKUP_IO, 0); gpio_direction_input(USB_WKUP_IO); gpio_set_pull_up(USB_WKUP_IO, 0); gpio_set_pull_down(USB_WKUP_IO, 0); gpio_set_die(USB_WKUP_IO, 1); delay(10); } return (gpio_read(USB_WKUP_IO));//no usb charing == false #else return 0; #endif } unsigned char read_power_key() { unsigned char usb_wk; static unsigned char pkey_init = 0; if (!pkey_init) { pkey_init = 1; gpio_latch_en(PORT_WAKEUP_IO, 0); gpio_direction_input(PORT_WAKEUP_IO); gpio_set_pull_up(PORT_WAKEUP_IO, 0); gpio_set_pull_down(PORT_WAKEUP_IO, 0); gpio_set_die(PORT_WAKEUP_IO, 1); delay(200); } delay_us(3000); return !gpio_read(PORT_WAKEUP_IO); return 0; } unsigned int get_usb_wkup_gpio() { return (USB_WKUP_IO); } /*进软关机之前默认将IO口都设置成高阻状态，需要保留原来状态的请修改该函数*/ static void board_set_soft_poweroff(void) { u32 IO_PORT; JL_PORT_FLASH_TypeDef *gpio[] = {JL_PORTA, JL_PORTB, JL_PORTC, JL_PORTD, JL_PORTE, JL_PORTF, JL_PORTG, JL_PORTH}; for (u8 p = 0; p < 8; ++p) { //flash sdram PD PE PF PG口不能进行配置,由内部完成控制 if (gpio[p] == JL_PORTD || gpio[p] == JL_PORTE || gpio[p] == JL_PORTF || gpio[p] == JL_PORTG) { continue; } for (u8 i = 0; i < 16; ++i) { IO_PORT = IO_PORTA_00 + p * 16 + i; gpio_set_pull_up(IO_PORT, 0); gpio_set_pull_down(IO_PORT, 0); gpio_set_direction(IO_PORT, 1); gpio_set_die(IO_PORT, 0); gpio_set_dieh(IO_PORT, 0); gpio_set_hd(IO_PORT, 0); gpio_set_hd1(IO_PORT, 0); gpio_latch_en(IO_PORT, 1); } } #ifdef PORT_VCC33_CTRL_IO gpio_latch_en(PORT_VCC33_CTRL_IO, 0); gpio_direction_output(PORT_VCC33_CTRL_IO, 0); gpio_set_pull_up(PORT_VCC33_CTRL_IO, 0); gpio_set_pull_down(PORT_VCC33_CTRL_IO, 1); gpio_set_direction(PORT_VCC33_CTRL_IO, 1); gpio_set_die(PORT_VCC33_CTRL_IO, 0); gpio_set_dieh(PORT_VCC33_CTRL_IO, 0); gpio_latch_en(PORT_VCC33_CTRL_IO, 1); #endif } static void sleep_exit_callback(u32 usec) { #ifdef PORT_VCC33_CTRL_IO gpio_direction_output(PORT_VCC33_CTRL_IO, 1); gpio_set_pull_up(PORT_VCC33_CTRL_IO, 1); gpio_set_pull_down(PORT_VCC33_CTRL_IO,0); #endif /* putchar('-'); */ } static void sleep_enter_callback(u8 step) { /* 此函数禁止添加打印 */ if (step == 1) { /*dac_power_off();*/ } else { #ifdef PORT_VCC33_CTRL_IO gpio_direction_output(PORT_VCC33_CTRL_IO, 0); gpio_set_pull_up(PORT_VCC33_CTRL_IO, 0); gpio_set_pull_down(PORT_VCC33_CTRL_IO, 1); gpio_set_direction(PORT_VCC33_CTRL_IO, 1); gpio_set_die(PORT_VCC33_CTRL_IO, 0); #endif } } static void board_power_init(void) { gpio_direction_input(IO_PORTB_08); gpio_set_pull_up(IO_PORTB_08,0); gpio_set_pull_down(IO_PORTB_08,0); gpio_direction_input(IO_PORTC_05); gpio_set_pull_up(IO_PORTC_05,0); gpio_set_pull_down(IO_PORTC_05,0); gpio_direction_input(IO_PORTH_07); gpio_set_pull_up(IO_PORTH_07,0); gpio_set_pull_down(IO_PORTH_07,0); gpio_direction_input(IO_PORTH_06); gpio_set_pull_up(IO_PORTH_06,0); gpio_set_pull_down(IO_PORTH_06,0); #ifdef PORT_VCC33_CTRL_IO gpio_direction_output(PORT_VCC33_CTRL_IO, 1); gpio_set_pull_up(PORT_VCC33_CTRL_IO, 1); gpio_set_pull_down(PORT_VCC33_CTRL_IO,0); #endif power_init(&power_param); power_set_callback(TCFG_LOWPOWER_LOWPOWER_SEL, sleep_enter_callback, sleep_exit_callback, board_set_soft_poweroff); power_keep_state(POWER_KEEP_RESET);//0, POWER_KEEP_DACVDD | POWER_KEEP_RTC | POWER_KEEP_RESET #ifdef CONFIG_RTC_ENABLE power_keep_state(POWER_KEEP_RTC);//0, POWER_KEEP_DACVDD | POWER_KEEP_RTC | POWER_KEEP_RESET #endif power_wakeup_init(&wk_param); } #ifdef CONFIG_DEBUG_ENABLE void debug_uart_init() { uart_init(&uart2_data); } #endif void board_early_init() { dac_early_init(0, 0, 1000); devices_init(); } void board_init() { board_power_init(); #ifdef CONFIG_RTC_ENABLE rtc_early_init(); #endif adc_init(); #if (TCFG_IOKEY_ENABLE || TCFG_IRKEY_ENABLE || TCFG_RDEC_KEY_ENABLE || TCFG_ADKEY_ENABLE) key_driver_init(); #endif } #endif